Package 'sarp.snowprofile'

Description

Extract method

Usage

## S3 method for class 'snowprofileSet'
x[i]

Arguments

Value

snowprofileSet object

Description

Convert character aspects (of snow profile locations) to numeric values. For example, Aspect "N" (north) becomes 0 degrees azimuth.

Usage

char2numAspect(charAspect)

Arguments

Value

Float value of numeric aspect location, North = 0 degree, S = 180 degree

Author(s)

fherla

Examples

char2numAspect("W")
char2numAspect("WNW")

char2numAspect(c("N", NA, "NA", "NE"))

Description

Convert character hand hardness index (HHI) of snow layers to numeric values. For example, hand hardness Fist becomes 1, Ice becomes 6.

Usage

char2numHHI(charHHI)

Arguments

Value

Float value of numeric hand hardness level between 1 and 6.

Author(s)

fherla

Examples

char2numHHI('F+')
char2numHHI('F-')
char2numHHI('F-4F')

## not meaningful:
this_throws_error <- TRUE
if (!this_throws_error) {
char2numHHI('F-P')
}

Description

The function can compute the RTA index for layers and for interfaces. The calculation follows the example in Monti (2013), referenced below. The six individual relative lemons are computed as follows. To compute the RTA index for layers, the layer properties are combined with the interface properties of the weakest interface below or above the layer. To compute the RTA index for interfaces, the interface properties are combined with the weakest layer properties below or above the interface. The six properties considered in the index are

• grain size, hardness, grain type (layer properties)

• difference of grain sizes and hardness (at the interface)

• depth (at the top interface of the layer)

Instead of implementing a static threshold for the depth weighting, the depth is scaled with a weibull function that is corrected for potential crusts and their stabilizing effects (Monti and Mitterer, personal communication).

Note that due to the crust correction, the results from this function will only be correct if applied to profiles that have not yet been resampled (such as by functions from sarp.snowprofile.alignment: resampleSP, resampleSPpairs, dtw, averageSP).

The RTA index ranges between ⁠[0, 1]⁠, with the weakest layer/interface euqal to 1. Values > 0.8 indicate layers/interfaces with a poor structural stability.

Usage

computeRTA(x, target = c("interface", "layer"))

## S3 method for class 'snowprofileSet'
computeRTA(x, target = c("interface", "layer"))

## S3 method for class 'snowprofile'
computeRTA(x, target = c("interface", "layer"))

Arguments

Value

The input object will be returned with the new layer properties rta/rta_interface describing the RTA index added to the profile layers.

Methods (by class)

• computeRTA(snowprofileSet): for snowprofileSets

• computeRTA(snowprofile): for snowprofiles

Author(s)

fherla

References

Monti, F., & Schweizer, J. (2013). A relative difference approach to detect potential weak layers within a snow profile. Proceedings of the 2013 International Snow Science Workshop, Grenoble, France, 339–343. Retrieved from https://arc.lib.montana.edu/snow-science/item.php?id=1861

See Also

computeTSA

Examples

## apply function to snowprofileSet
profileset <- computeRTA(SPgroup)

## apply function to snowprofile and plot output
sp <- computeRTA(SPpairs$B_modeled1)
plot(sp, TempProfile = FALSE, main = "RTA")
lines(sp$layers$rta*5, sp$layers$height - 0.5*sp$layers$thickness, type = "b", xlim = c(0, 5))
lines(sp$layers$rta_interface*5, sp$layers$height, type = "b", xlim = c(0, 5), col = "red")
abline(h = sp$layers$height, lty = "dotted", col = "grey")
abline(v = 0.8*5, lty = "dashed")

Description

For each layer, compute the average density of all layers above, i.e. ⁠<rho>_slab⁠.

Usage

computeSLABrho(profile)

Arguments

Value

snowprofile object with added layers column ⁠$slab_rho⁠. Note that topmost layer is always NA.

Author(s)

fherla

Description

For each layer, compute the average density over grain size of all layers above, i.e. ⁠<rho/gs>_slab⁠. This variable has been found to characterize the cohesion of slabs: new snow slabs tend to consist of low density & large grains, and more cohesive slabs of older snow tend to consist of higher density & smaller grains (Mayer et al, 2022 in review).

Usage

computeSLABrhogs(profile, implementation = c("pub", "literal")[1])

Arguments

Value

snowprofile object with added layers column ⁠$slab_rhogs⁠. Note that topmost layer is always NA.

Author(s)

fherla

Description

This routine computes the traditional lemons (German 'Nieten') based on absolute thresholds. Since the thresholds are defined in Monti (2014) with different thresholds for manual versus observed profiles, this routine switches between the appropriate thresholds based on the ⁠$type⁠ field of the input profile. While manual and whiteboard profiles get one set of thresholds, modeled, vstation, and aggregate type profiles get another set.

Usage

computeTSA(x, target = c("interface", "layer"))

## S3 method for class 'snowprofileSet'
computeTSA(x, target = c("interface", "layer"))

## S3 method for class 'snowprofile'
computeTSA(x, target = c("interface", "layer"))

Arguments

Value

New layer properties tsa/tsa_interface describing the threshold sums are added to the profile layers. The TSA sums up to 6 indicators, whereas >= 5 indicators indicate structurally unstable layers/interfaces.

Methods (by class)

• computeTSA(snowprofileSet): for snowprofileSets

• computeTSA(snowprofile): for snowprofiles

Author(s)

fherla

References

Schweizer, J., & Jamieson, J. B. (2007). A threshold sum approach to stability evaluation of manual snow profiles. Cold Regions Science and Technology, 47(1–2), 50–59. https://doi.org/10.1016/j.coldregions.2006.08.011

Monti, F., Schweizer, J., & Fierz, C. (2014). Hardness estimation and weak layer detection in simulated snow stratigraphy. Cold Regions Science and Technology, 103, 82–90. https://doi.org/10.1016/j.coldregions.2014.03.009

See Also

computeRTA

Examples

## apply function to snowprofileSet
profileset <- computeTSA(SPgroup)

## apply function to snowprofile and plot output
sp <- computeTSA(SPpairs$B_modeled1)
plot(sp, TempProfile = FALSE, main = "TSA")
lines(sp$layers$tsa/6*5,
      sp$layers$height - 0.5*sp$layers$thickness, type = "b", xlim = c(0, 5))
lines(sp$layers$tsa_interface/6*5, sp$layers$height, type = "b", xlim = c(0, 5), col = "red")
abline(h = sp$layers$height, lty = "dotted", col = "grey")
abline(v = 5/6*5, lty = "dashed")

Description

This routine derives the datetags of simulated snow profile layers from deposition dates. Datetags usually are deposition dates for crust layers, and burial dates for other weak layers (e.g., SH, FC). If no datetags can be derived, a datetag column of NAs will nevertheless be added to the snowprofile layers. The routine also adds a bdate column for burial dates that are calculated along the way.

Usage

deriveDatetag(x, adjust_bdates = TRUE, ...)

## S3 method for class 'snowprofileSet'
deriveDatetag(x, adjust_bdates = TRUE, ...)

## S3 method for class 'snowprofile'
deriveDatetag(x, adjust_bdates = TRUE, ...)

## S3 method for class 'snowprofileLayers'
deriveDatetag(x, adjust_bdates = TRUE, checkMonotonicity = TRUE, ...)

Arguments

Details

bdates are computed by taking the ddate of the overlying layer. For snowpack simulations with thin layer resolution, this approach yields very similar ddates and bdates for most layers, since most layers form and instantly get buried by another layer of the same storm. To make bdates more similar to human interpretation, bdates can be adjusted, so that (similar) layers with the same ddate (i.e., same storm) inherit the same bdate (similar means: identical gtype & hardness).

Value

The input object will be returned with the columns datetag and bdate added to the profile layers

Methods (by class)

• deriveDatetag(snowprofileSet): for snowprofileSets

• deriveDatetag(snowprofile): for snowprofiles

• deriveDatetag(snowprofileLayers): for snowprofileLayers

Author(s)

fherla

Examples

## This is not the most meaningful example, but it nicely illustrates the routine:
print(SPpairs$A_manual)

(A_addedDatetags <- deriveDatetag(SPpairs$A_manual))

Description

Export or write a snowprofile object to a CSV table

Usage

export.snowprofileCsv(
  profile,
  filename = stop("filename must be provided"),
  sep = ",",
  export.all = "Layers",
  variables = NA
)

Arguments

Details

Note that existing files with the specified filename will be overwritten without warning!

Value

Writes csv file to disk, no return value in R

Author(s)

fherla

See Also

snowprofileCsv

Examples

## export an entire snowprofile object:

export.snowprofileCsv(SPpairs$A_manual, filename = file.path(tempdir(), 'file.csv'),
                      export.all = TRUE)


## export only the layer properties of a snowprofile object,
#  and change the column order with few column names:
#  All layer variables will be exported, but the three ones provided in 'variables'
#  will be the first three columns of the csv table, and their column names will be changed
#  accordingly.

export.snowprofileCsv(SPpairs$A_manual, filename = file.path(tempdir(), 'file.csv'),
                      export.all = 'Layers',
                      variables = list(height = 'height_top', hardness = 'hardness',
                                       gtype = 'gt1'))


## export all layer properties of a snowprofile object plus the station ID:

export.snowprofileCsv(SPpairs$A_manual, filename = file.path(tempdir(), 'file.csv'),
                      export.all = 'Layers', variables = list(station_id = 'station_id'))

## check the content of the exported csv file:
csv_content <- read.csv(file.path(tempdir(), 'file.csv'))
head(csv_content)

## or re-import the csv file as snowprofile object:
csv_snowprofile <- snowprofileCsv(file.path(tempdir(), 'file.csv'))
print(csv_snowprofile)

Description

Find one or more layers of interest, such as persistent weak layers (PWL) in a snowprofile or snowprofileLayers object based on combinations of grain type, datetag, grain size, and stability indices (TSA/ RTA/ critical crack length/ p_unstable) of the layer. The routine can also be used for searching for crusts (or any other grain types).

Usage

findPWL(
  x,
  pwl_gtype = c("SH", "DH"),
  pwl_date = NA,
  date_range = c(-5, 0),
  date_range_earlier = as.difftime(date_range[1], units = "days"),
  date_range_later = as.difftime(date_range[2], units = "days"),
  bdate_range = c(-1, 1),
  bdate_range_earlier = as.difftime(bdate_range[1], units = "days"),
  bdate_range_later = as.difftime(bdate_range[2], units = "days"),
  threshold_gtype = pwl_gtype,
  threshold_gsize = NA,
  threshold_TSA = NA,
  threshold_RTA = NA,
  threshold_SK38 = NA,
  threshold_RC = NA,
  threshold_PU = NA
)

labelPWL(x, ...)

Arguments

Details

In case date considerations are included in your search, either one of the date window conditions needs to be satisfied to return a given layer:

• ddate or datetag within date_range, or

• bdate within bdate_range

If the input object contains deposition dates (ddate, mostly in simulated profiles), but no bdates, they are automatically computed by deriveDatetag; otherwise the date window is applied to the datetag (mostly for manual profiles).

If you apply thresholds to your search, only layers are returned that satisfy at least one of the provided thresholds.

The labelPWL wrapper function is primarily used by sarp.snowprofile.alignment::averageSP.

Value

findPWL: An index vector of PWLs that match the desired requirements

labelPWL: The input object with an extra boolean column appended to the layer object, called ⁠$layerOfInterest⁠.

Functions

• findPWL(): Find layers of interest (e.g., PWLs) in snowprofile or snowprofileLayers

• labelPWL(): Label layers of interest (e.g., weak layers) in snowprofile

Author(s)

fherla

Examples

## get index vector:
findPWL(SPpairs$A_modeled)

## get layers subset:
SPpairs$A_manual$layers[findPWL(SPpairs$A_manual), ]
SPpairs$A_manual$layers[findPWL(SPpairs$A_manual, threshold_gsize = 2.2,
                        threshold_gtype = c("FC", "FCxr")), ]
## all (SH, DH), and (FC, FCxr) >= 1 mm grain size:
SPpairs$A_modeled$layers[findPWL(SPpairs$A_modeled, pwl_gtype = c("SH", "DH", "FC", "FCxr"),
                                 threshold_gsize = 1, threshold_gtype = c("FC", "FCxr")), ]
## use TSA threshold:
SPpairs$A_modeled <- computeTSA(SPpairs$A_modeled)
SPpairs$A_modeled$layers[findPWL(SPpairs$A_modeled, pwl_gtype = c("SH", "DH", "FC", "FCxr"),
                                 threshold_TSA = 4, threshold_gtype = c("FC", "FCxr")), ]

## searching for a specific pwl_date:
## let's construct one layer and an array of pwl_dates
tl <- snowprofileLayers(height = 1, gtype = "SH",
                        ddate = as.POSIXct("2020-12-15"),
                        bdate = as.POSIXct("2020-12-20"))
pwl_dates <- paste0("2020-12-", seq(14, 22))
## which pwl_date will 'find' that layer?
sapply(pwl_dates, function(dt) length(findPWL(tl, pwl_date = dt)) > 0)
## same example, but with bdate being NA:
tl <- snowprofileLayers(height = 1, gtype = "SH",
                        ddate = as.POSIXct("2020-12-15"),
                        bdate = as.POSIXct(NA), dropNAs = FALSE)
sapply(pwl_dates, function(dt) length(findPWL(tl, pwl_date = dt)) > 0)

## pwl_date example with proper profile:
sp <- deriveDatetag(SPpairs$A_manual)
sp$layers
pwl_dates <- paste0("2019-02-", seq(18, 26))
names(pwl_dates) <- pwl_dates
## which pwl_date will 'find' the two layers with (b)date labels?
list(pwl_date = lapply(pwl_dates, function(dt) {
  sp$layers[findPWL(sp, pwl_gtype = c("SH", "FC"), pwl_date = dt),
            c("height", "gtype", "ddate", "bdate")]
}))

## same example as above, but including TSA threshold:
sp <- computeTSA(sp)
## the SH layer has TSA 5, the FC layer has TSA 4:
list(pwl_date = lapply(pwl_dates, function(dt) {
  sp$layers[findPWL(sp, pwl_gtype = c("SH", "FC"), pwl_date = dt, threshold_TSA = 5),
            c("height", "gtype", "ddate", "bdate")]
}))
## --> no more FC layer in output since its TSA value is below the threshold!

## can also be used to search for crusts:
SPpairs$A_manual$layers[findPWL(SPpairs$A_manual, pwl_gtype = "MFcr"), ]

Description

Calculate missing data.frame columns based on the given ones, if possible.

Usage

format_snowprofileLayers(
  obj,
  target = "all",
  hs = NA,
  maxObservedDepth = NA,
  validate = TRUE,
  dropNAs = TRUE
)

Arguments

Value

copy of obj with auto-filled columns

Description

Gets colours for plotting snow density values in snowprofiles. Colours are consistent with niViz at https://niviz.org

Usage

getColoursDensity(Values, Resolution = 101, Verbose = FALSE)

Arguments

Value

Array with HTML colour codes

Author(s)

phaegeli

See Also

getColoursGrainSize, getColoursGrainType, getColoursHardness, getColoursLWC, getColoursSnowTemp

Examples

Density <- seq(0,700, by=10)
plot(x = rep(1,length(Density)), y = Density, col = getColoursDensity(Density), pch = 19, cex = 3)

Description

Gets colours for plotting grain size values in snowprofiles. Colours are consistent with niViz at https://niviz.org

Usage

getColoursGrainSize(Values, Resolution = 101, Verbose = FALSE)

Arguments

Value

Array with HTML colour codes

Author(s)

phaegeli

See Also

getColoursDensity, getColoursGrainType, getColoursHardness, getColoursLWC, getColoursSnowTemp

Examples

GrainSize <- seq(0,6, by=0.1)
plot(x = rep(1,length(GrainSize)), y = GrainSize,
     col = getColoursGrainSize(GrainSize), pch = 19, cex = 3)

Description

Grain colours are defined in the grainDict data.frame and the definitions can be changed with setColoursGrainType

Usage

getColoursGrainType(Grains, grainDict. = grainDict)

Arguments

Value

Array with HTML colour codes

Author(s)

phaegeli, shorton, fherla

See Also

setColoursGrainType, getColoursDensity, getColoursGrainSize, getColoursHardness, getColoursLWC, getColoursSnowTemp

Examples

Grains <- c('PP', 'DF', 'RG', 'FC', 'FCxr', 'DH', 'SH', 'MF', 'MFcr', 'IF')
Colours <- getColoursGrainType(Grains)
Colours

plot(1:length(Grains), col = Colours, pch = 20, cex = 3)
text(1:length(Grains), 1:length(Grains), Grains, pos = 1)

Description

Gets colours for plotting snow hardness values in snowprofiles.

Usage

getColoursHardness(Values, Resolution = 101, Verbose = FALSE)

Arguments

Value

Array with HTML colour codes

Author(s)

phaegeli

See Also

getColoursDensity, getColoursGrainSize, getColoursGrainType, getColoursLWC, getColoursSnowTemp

Examples

Hardness <- c(1:5)
plot(x = rep(1,length(Hardness)), y = Hardness,
     col = getColoursHardness(Hardness), pch = 19,cex = 3)

Description

Gets colours for plotting LWC values in snowprofiles. Colours are consistent with niViz at https://niviz.org

Usage

getColoursLWC(Values, Resolution = 101, Verbose = FALSE)

Arguments

Value

Array with HTML colour codes

Author(s)

phaegeli

See Also

getColoursDensity, getColoursGrainSize, getColoursGrainType, getColoursHardness, getColoursSnowTemp

Examples

LWC <- seq(0,6, by = 0.1)
plot(x = rep(1,length(LWC)), y = LWC, col = getColoursLWC(LWC), pch = 19, cex = 3)

Description

Gets colours for plotting the snow layer property 'percentage', as used for example for distributions from 0–1.

Usage

getColoursPercentage(
  Values,
  Resolution = 101,
  Min = 0,
  Max = 1,
  ClrRamp = c("Blues", "Greys", "Greys_transparent")[1]
)

Arguments

Value

Array with HTML colour codes

Author(s)

fherla

See Also

getColoursGrainSize, getColoursGrainType, getColoursHardness, getColoursLWC, getColoursSnowTemp, getColoursStability

Examples

prct <- seq(0, 1, by=0.1)
plot(x = rep(1,length(prct)), y = prct,
     col = getColoursPercentage(prct), pch = 19, cex = 3)

plot(x = rep(1,length(prct)), y = prct,
     col = getColoursPercentage(prct, ClrRamp = "Greys"), pch = 19, cex = 3)

Description

Gets colours for plotting snow temperature values in snowprofiles. Colours are consistent with niViz at https://niviz.org

Usage

getColoursSnowTemp(Values, Resolution = 101, Verbose = FALSE)

Arguments

Value

Array with HTML colour codes

Author(s)

phaegeli

See Also

getColoursDensity, getColoursGrainSize, getColoursGrainType, getColoursHardness, getColoursLWC

Examples

SnowTemp <- c(-25:0)
plot(x = rep(1,length(SnowTemp)), y = SnowTemp,
     col = getColoursSnowTemp(SnowTemp), pch = 19,cex = 3)

Description

Gets colours for plotting snow stability indices in snowprofiles.

Usage

getColoursStability(
  Values,
  StabilityIndexThreshold = 0.77,
  StabilityIndexRange = c(0, 1),
  invers = FALSE,
  Resolution = 100
)

Arguments

Value

Array with HTML colour codes

Author(s)

fherla

See Also

getColoursGrainSize, getColoursGrainType, getColoursHardness, getColoursLWC, getColoursSnowTemp, getColoursPercentage

Examples

p_unstable <- seq(0, 1, by=0.1)
plot(x = rep(1,length(p_unstable)), y = p_unstable,
     col = getColoursStability(p_unstable), pch = 19, cex = 3)

critical_crack_length <- c(seq(0.2, 0.8, by=0.1), 1.5, 2.5)
plot(x = rep(1,length(critical_crack_length)), y = critical_crack_length, pch = 19, cex = 3,
     col = getColoursStability(critical_crack_length, StabilityIndexThreshold = 0.4,
                               StabilityIndexRange = c(0, 3), invers = TRUE))

Description

The colours can be changed by calling the function setColoursGrainType, see examples below.

Usage

grainDict

Format

A data.frame

Examples

print(grainDict)

## change colours for subsequent plots:
grainDict <- setColoursGrainType('sarp-reduced')

Description

Check whether a profile is observed down to ground or not

Usage

hasUnobservedBasalLayer(x)

Arguments

Value

boolean TRUE/FALSE

Description

Import R_DEFAULT_PACKAGES

Usage

importRDefaultPackages()

Description

Insert a special layer at the bottom to indicate a snow profile that's unobserved from a specific point down to the ground internal function, not exported. used in snowprofileLayers

Usage

insertUnobservedBasalLayer(object, basal_offset, setBasalThicknessNA = FALSE)

Arguments

Value

same object with basal layer inserted as individual row in the data.frame

Author(s)

fherla

Description

Check if object is of class snowprofile

Usage

is.snowprofile(x)

Arguments

Value

boolean

Description

Check if object is of class snowprofileInstabilitySigns

Usage

is.snowprofileInstabilitySigns(x)

Arguments

Value

boolean

Description

Check if object is of class snowprofileLayers

Usage

is.snowprofileLayers(x)

Arguments

Value

boolean

Description

Check if object is of class snowprofileSet

Usage

is.snowprofileSet(x)

Arguments

Value

boolean

Description

Check if object is of class snowprofileTests

Usage

is.snowprofileTests(x)

Arguments

Value

boolean

Description

Low-cost, efficient constructor function to be used by users who know what they're doing. If that's not you, use the high-level constructor snowprofile.

Usage

new_snowprofile(
  station = character(),
  station_id = character(),
  datetime = as.POSIXct(NA),
  latlon = as.double(c(NA, NA)),
  elev = double(),
  angle = double(),
  aspect = double(),
  hs = double(),
  maxObservedDepth = double(),
  type = character(),
  band = character(),
  zone = character(),
  comment = character(),
  hn24 = double(),
  hn72 = double(),
  ski_pen = double(),
  layers = snowprofileLayers(),
  tests = snowprofileTests(),
  instabilitySigns = snowprofileInstabilitySigns()
)

Arguments

Value

snowprofile object

Description

This is a wrapper function to bin several weak layers (or crusts) into vertical levels. The layers to be binned can be controlled with a provided index vector for full customization.

Usage

numberOfPWLsPerVerticalLevel(x, pwl_idx, depth_breaks = c(0, 30, 80, 150, Inf))

Arguments

Value

This function returns a table object

Author(s)

fherla

Examples

SH_idx <- findPWL(SPpairs$C_day1, pwl_gtype = "SH")
numberOfPWLsPerVerticalLevel(SPpairs$C_day1, SH_idx)

numberOfPWLsPerVerticalLevel(SPpairs$C_day2, findPWL(SPpairs$C_day2))

Description

Plot hardness profile

Usage

## S3 method for class 'snowprofile'
plot(
  x,
  TempProfile = TRUE,
  xlimTemp = NULL,
  Col = "auto",
  TopDown = "auto",
  axes = TRUE,
  xlab = "",
  emphasizeLayers = FALSE,
  emphasis = "95",
  failureLayers = FALSE,
  failureLayers.cex = 1,
  failureLayers.col = "red",
  nYTicks = 4,
  ymax = max(c(x$maxObservedDepth, x$hs), na.rm = TRUE),
  alignWithBottomUpPlot = FALSE,
  highlightUnobservedBasalLayers = TRUE,
  label.datetags = FALSE,
  ...
)

Arguments

See Also

plot.snowprofileSet

Examples

plot(SPpairs$A_manual)
plot(SPpairs$A_manual, Col = 'black')
plot(SPpairs$A_manual, emphasizeLayers = c(5, 11),
     failureLayers = SPpairs$A_manual$layers$height[5], failureLayers.cex = 1.5)
plot(SPpairs$A_manual, emphasizeLayers = 'SH')
plot(SPpairs$A_manual, TopDown = TRUE)
plot(SPpairs$A_modeled, TempProfile = TRUE, xlimTemp = c(-30,10))

# highlight unobserved basal layers:
plot(snowprofile(layers = snowprofileLayers(depth = c(40, 25, 0),
                                               hardness = c(2, 3, 1),
                                               gtype = c('FC', NA, 'PP'),
                                               hs = 70,
                                               maxObservedDepth = 50)), TopDown = TRUE, ymax = 80)

Description

A flexible function to plot multiple snowprofiles either in a timeseries or various types of groups.

Usage

## S3 method for class 'snowprofileSet'
plot(
  x,
  SortMethod = c("time", "unsorted", "hs", "elev", "presorted"),
  ColParam = c("gtype", "hardness", "density", "temp", "gsize", "ssi", "p_unstable",
    "crit_cut_length", "rta", "percentage"),
  TopDown = FALSE,
  DateStart = NA,
  DateEnd = NA,
  Timeseries_labels = c("weekly", "monthly", NA),
  ylim = NULL,
  OutlineLyrs = FALSE,
  emphasizeLayers = NULL,
  colAlpha = NA,
  colEmphasis = NA,
  OutlineProfile = NULL,
  HorizGrid = TRUE,
  VerticalGrid = TRUE,
  yaxis = TRUE,
  main = NA,
  ylab = NA,
  xlab = NA,
  box = TRUE,
  xticklabels = FALSE,
  xtick.las = 2,
  yPadding = 10,
  xPadding = 0.5,
  hardnessResidual = 1,
  hardnessScale = 1,
  hardnessOffset = -0.5,
  k = NULL,
  offset = as.Date(NA),
  add = FALSE,
  ...
)

Arguments

Details

The routine allows you to plot coloured sequences only, or to include hardness profile information as well. See parameter hardnessResidual and the examples for more details. To change the font size of labels etc, use par() with the parameters cex.lab, cex.axis, etc.

Author(s)

shorton, fherla, phaegeli

See Also

plot.snowprofile, SPgroup

Examples

## Standard profile timeline (e.g. https://niviz.org)
plot(SPtimeline)

## Group of profiles with same timestamp
plot(SPgroup, SortMethod = 'unsorted')  # sorted in same order as list
plot(SPgroup, SortMethod = 'hs') # sorted by snow height
plot(SPgroup, SortMethod = 'elev') # sorted by elevation

## Colour layers by other properties
plot(SPtimeline, ColParam = 'density')

## Align layers by depth instead of height
plot(SPtimeline, TopDown = TRUE)

## Timelines with specific date ranges
plot(SPtimeline, DateEnd = '2017-12-17')
plot(SPtimeline, DateStart = '2017-12-15', DateEnd = '2017-12-17')

## Show hardness profile, too:
plot(SPtimeline, hardnessResidual = 0.5)

## Additional examples of plot dimensions and labelling
## Label the indices of the profiles in the list:
plot(SPgroup, SortMethod = 'elev', xticklabels = "originalIndices")
##  ... and with minimized axis limits and their station ID names:
plot(SPgroup, SortMethod = 'elev', xticklabels = sapply(SPgroup, function(x) x$station_id),
       yPadding = 0, xPadding = 0, xaxs = 'i', yaxs = 'i')
##  sorted by depth, and without box:
plot(SPgroup, SortMethod = 'hs', TopDown = TRUE, box = FALSE)

## Apply a date offset to investigate which layers formed around that day of interest:
pwl_exists <- sapply(SPgroup, function(sp)
  {length(findPWL(sp, pwl_date = "2019-01-21", pwl_gtype = c("SH", "DH"),
                  date_range_earlier = as.difftime(2, unit = "days"))) > 0})
k <- order(pwl_exists, decreasing = TRUE)
plot(SPgroup, SortMethod = 'presorted', k = k, xticklabels = "originalIndices",
     offset = as.Date("2019-01-21"), xlab = "<-- Jan 21 PWL exists | does not exist -->")
abline(v = max(which(pwl_exists[k]))+0.5, lty = "dashed")

## Emphasize specific layers
## (i) all labeled layers of interest:
SPgroup <- snowprofileSet(lapply(SPgroup, labelPWL))  # label layers with default settings
plot(SPgroup, SortMethod = "hs", emphasizeLayers = TRUE, colAlpha = 0.3)
## (ii) specific individual layers:
plot(SPgroup, SortMethod = "hs",
     emphasizeLayers = list(pwl_gtype = c("SH", "DH"), pwl_date = "2019-01-21"),
     colAlpha = 0.3, colEmphasis = "black")

Description

Print snowprofile object

Usage

## S3 method for class 'snowprofile'
print(x, pretty = TRUE, nLayers = NA, ...)

Arguments

Value

object gets printed to console

Examples

## pretty print
SPpairs$A_manual
## or alternatively:
print(SPpairs$A_manual)
## reduce number of layers printed:
print(SPpairs$A_manual, nLayers = 6)

## print profile non-pretty (i.e., like the data is stored):
print(SPpairs$A_manual, pretty = FALSE)

Description

Convert snowprofile object into data.frame with a row for each layer and additional columns with metadata

Usage

## S3 method for class 'snowprofile'
rbind(..., deparse.level = 1)

Arguments

Details

Metadata columns are calculated with summary.snowprofile

Value

data.frame

Author(s)

shorton

See Also

summary.snowprofile, rbind.snowprofileSet

Examples

Profile <- SPgroup[[1]]
ProfileTable <- rbind(Profile)
head(ProfileTable)

Description

A wrapper to apply rbind.snowprofile to each profile in a snowprofileSet then concatenate

Usage

## S3 method for class 'snowprofileSet'
rbind(..., deparse.level = 1)

Arguments

Details

Returns a large data.frame with a row for each layer and additional columns with metadata (calculated with summary.snowprofile)

Value

data.frame

Author(s)

shorton

See Also

summary.snowprofile, rbind.snowprofile

Examples

## Create rbind table
ProfileTable <- rbind(SPgroup)
head(ProfileTable)

## Filter by layer properties
SHlayers <- subset(ProfileTable, gtype == 'SH')
summary(SHlayers)
plot(elev ~ gsize, SHlayers)

Description

Read contents of a SMET file https://models.slf.ch/docserver/meteoio/SMET_specifications.pdf

Usage

readSmet(Filename)

Arguments

Value

List containing metadata and data

Author(s)

shorton

See Also

writeSmet, snowprofileSno, snowprofilePrf, snowprofilePro

Examples

## Path to example smet
Filename <- system.file('extdata', 'example.smet', package = 'sarp.snowprofile')
Wx = readSmet(Filename)
str(Wx)

Description

Reformat a malformatted snowprofile object. A malformatted object may use field names that deviate from our suggested field names (e.g., grain_type instead of gtype), or it may use data types that are different than what we suggest to use (e.g., ddate as type Date instead of POSIXct). Basically, if your snowprofile object fails the test of validate_snowprofile due to the above reason this function should fix it.

Usage

reformat_snowprofile(profile, currentFields = NULL, targetFields = NULL)

Arguments

Examples

## check the malformatted profile:
this_throws_error <- TRUE
if (!this_throws_error) {
validate_snowprofile(SPmalformatted[[1]])
}
## i.e., we see that elev and ddate are of wrong data type,
## and a warning that grain_type is an unknown layer property.

## reformat field types, but not the field name:
betterProfile <- reformat_snowprofile(SPmalformatted[[1]])
## i.e., no error is raised anymore, but only the grain_type warning

## so let's reformat also the field names:
optimalProfile <- reformat_snowprofile(SPmalformatted[[1]], "grain_type", "gtype")



## reformat a list of profiles with the same configuration:
SPmalformatted_reformatted <- lapply(SPmalformatted, reformat_snowprofile,
                                     currentFields = "grain_type", targetFields = "gtype")

## the malformatted profile set finally is correctly formatted:
lapply(SPmalformatted_reformatted, validate_snowprofile)

Description

Before reading entire SNOWPACK output it can be helpful to scan the profile timestamps first

Usage

scanProfileDates(Filename, tz = "UTC")

Arguments

Value

vector of as.POSIXct timestamps

Author(s)

shorton

See Also

snowprofilePrf, snowprofilePro

Examples

## Path to example prf file
Filename <- system.file('extdata', 'example.prf', package = 'sarp.snowprofile')

## Scan dates in file
Dates <- scanProfileDates(Filename)
print(Dates)

Description

fast uncorrected sample standard deviation https://en.wikipedia.org/wiki/Standard_deviation#Rapid_calculation_methods

Usage

sd_sample_uncorrected(x, xbar = mean(x), na.rm = FALSE)

Arguments

Value

uncorrected sample standard deviation (i.e., a numeric scalar)

Author(s)

fherla

Description

Currently, you can choose between 'iacs', 'iacs2', 'sarp', or 'sarp-reduced'.

Usage

setColoursGrainType(ScaleName)

Arguments

Value

data.frame containing the new colour values stored in grainDict

References

Horton, S., Nowak, S., and Haegeli, P.: Enhancing the operational value of snowpack models with visualization design principles, Nat. Hazards Earth Syst. Sci., 20, 1557–1572, doi:10.5194/nhess-20-1557-2020, 2020.

See Also

grainDict, getColoursGrainType

Examples

## Current/default grain type colours
grainDict
plot(SPpairs$A_manual, main = 'Snow profile with default colours')

## Change to IACS colours
grainDict <- setColoursGrainType('IACS')
grainDict
plot(SPpairs$A_manual, main = 'Snow profile with IACS colours')

## Change to IACS colours with adjusted MFcr (darkred)
grainDict <- setColoursGrainType('IACS2')
grainDict
plot(SPpairs$A_manual, main = 'Snow profile with IACS colours and adjusted darkred MFcr')

## Change to SARP colours
grainDict <- setColoursGrainType('SARP')
grainDict
plot(SPpairs$A_manual, main = 'Snow profile with SARP colours')

## Change to reduced SARP colours
grainDict <- setColoursGrainType('SARP-reduced')
grainDict
plot(SPpairs$A_manual, main = 'Snow profile with a reduced set of SARP colours')

Description

The IACS records grain types in major and minor classes, e.g. precipitation particles PP can be subclassified into stellar dendrites PPsd. Some of these subclasses are not supported in this R package and so this function simplifies the unsupported gran type subclasses into their supported main classes. If a given grain type cannot be simplified, a NA value is returned for it.

Usage

simplifyGtypes(gtypes, supported_gtypes = grainDict$gtype)

Arguments

Value

the modified input array

Author(s)

fherla

Examples

## create an array of gtypes
gtypes <- c('FCxr', 'RGxf', 'PPsd', 'PP', 'IFrc', "KKfx")

## sinplify gtypes to supported_gtypes:
simplifyGtypes(gtypes)

Description

Conveniently create a snowprofile object. Calls low-level constructor (only available internally: new_snowprofile), asserts correctness through a snowprofile validator function (validate_snowprofile) and yields meaningful error messages. Use low-level constructor if you generate many (!) profiles.

Usage

snowprofile(
  station = as.character(NA),
  station_id = as.character(NA),
  datetime = as.POSIXct(NA),
  latlon = as.double(c(NA, NA)),
  elev = as.double(NA),
  angle = as.double(NA),
  aspect = as.double(NA),
  hs = as.double(NA),
  maxObservedDepth = as.double(NA),
  type = "manual",
  band = as.character(NA),
  zone = as.character(NA),
  comment = as.character(NA),
  hn24 = as.double(NA),
  hn72 = as.double(NA),
  ski_pen = as.double(NA),
  layers = snowprofileLayers(dropNAs = FALSE, validate = FALSE),
  tests = snowprofileTests(dropNAs = FALSE),
  instabilitySigns = snowprofileInstabilitySigns(dropNAs = FALSE),
  validate = TRUE,
  dropNAs = TRUE
)

Arguments

Value

snowprofile object

Author(s)

shorton, fherla

See Also

summary.snowprofile, plot.snowprofile, snowprofileLayers, snowprofileTests, snowprofileInstabilitySigns, SPpairs

Examples

## Empty snowprofile:
snowprofile()

## Test profile:
testProfile <- snowprofile(station = 'SARPstation', station_id = 'SARP007',
                           datetime = as.POSIXct('2019/04/01 10:00:00', tz = 'PDT'),
                           latlon = c(49.277223, -122.915084), aspect = 180,
                           layers = snowprofileLayers(height = c(10, 25, 50),
                                                      hardness = c(3, 2, 1),
                                                      gtype = c('FC', NA, 'PP')))
summary(testProfile)
plot(testProfile)

Description

Note, that this function only provides a starting point for loading caaml files into R. Currently, caaml files exported from niviz.org, or snowpilot.org should be compatible with this routine. However, this routine only extracts some metadata and some of the most important layer characteristics. While a temperature profile (that is independent from the layers) is extracted, no other variables that can be written into a caaml file are currently being read (such as stability test results, etc).

Usage

snowprofileCaaml(
  caamlFile,
  sourceType = NA,
  readStabilityTests = TRUE,
  validate = TRUE
)

Arguments

Details

• There is still a bug related to non-numeric aspects (e.g., E instead of 90).

• The snowprofileCsv function provides a lot more flexibility to read in data, if you can choose the format of your underlying data. Don't hesitate to reach out though if your caaml files throw errors and you need help! If you extend this routine, please also reach out and let us know, so we can update this package with your code extensions.

Value

snowprofile object

Author(s)

fherla

Examples

## load example caaml file that ships with package:
caamlFile <- system.file('extdata', 'example.caaml', package = 'sarp.snowprofile')

## read caaml file:
profile <- snowprofileCaaml(caamlFile, sourceType = 'vstation')

## other file with slighlty different xml namespace, structure, etc (including stability test):
caamlFile2 <- system.file('extdata', 'example2.caaml', package = 'sarp.snowprofile')
profile2 <- snowprofileCaaml(caamlFile2, sourceType = 'manual')

Description

Read csv file into a snowprofile object

Usage

snowprofileCsv(
  path,
  header = TRUE,
  sep = ",",
  use.swisscode = FALSE,
  height = "height",
  gtype = "gtype",
  hardness = "hardness",
  ...,
  crust.val = 2,
  tz = "UTC"
)

Arguments

Details

The minimum information required to construct a valid snowprofile object is height, gtype and hardness. Currently, substituting height with a depth vector is not supported.

If profile specific information is provided in the csv table, it can only be included into the snowprofile object through the exact field names (see above). However, layer specific information can be named arbitrarily (except for the three required fields).

Regarding swisscode: The SNOWPACK documentation specifies that MFcr are encoded as (gt1|gt2|gt3) = (7|x|2), i.e. gt1 == 7 and gt3 == 2. This is also how this routine handles the grain type encoding per default. However, some csv tables might be provided using swisscode encoding and providing gt1, gt2, and gt3 as individual one-digit columns. In those cases, gt3 could be defined as a boolean (0 or 1), where gt1 == 7 and gt3 == 1 represent crusts, instead of the aforementioned standard definition of gt1 == 7 and gt3 == 2. To handle these cases, crust.val can be set to 1, instead of its default crust.val = 2.

Value

snowprofile object

Author(s)

fherla

See Also

snowprofileCsv_advanced

Examples

## imagine a csv table with a very straightforward format,
## similar to the following data.frame:
(DF <- data.frame(height = c(50, 80, 100), gtype = c('FC', 'RG', 'PP'), hardness = c(1, 3, 2)))
## write DF to a temporary file:
write.csv(DF, file = file.path(tempdir(), 'file.csv'))

## read this file very easily by
profile <- snowprofileCsv(file.path(tempdir(), 'file.csv'))
profile


## imagine a csv table that requires a bit more customization,
## similar to the following data.frame:
(DF <- data.frame(ID = rep(1234, times = 3), layer_top = c(10.5, 15, 55.0), gt1 = c(5, 7, 2),
                  gs = c(5.0, 1.5, 1.0), crust = c(0, 1, 0), hardness = c('F', 'P', '4F+')))
write.csv(DF, file = file.path(tempdir(), 'file.csv'))

profile <- snowprofileCsv(file.path(tempdir(), 'file.csv'), height = 'layer_top', gtype = 'gt1',
                          use.swisscode = TRUE, gsize = 'gs', crust.val = 1)
profile
## Note that the csv column 'crust', which specifies whether a MF layer is actually
#  a MFcr layer, is already named correctly (i.e., 'crust'). If it were named 'freeze-crust',
#  we would need to add to the function call: `crust = 'freeze-crust'`.
# Also note, that we need to provide `crust.val = 1`, since we're not using the standard definition
# of swisscode MFcr encoding (see Details).

## let's assume you want to read the csv file an customize some names, e.g. GrainSIZE:
profile <- snowprofileCsv(file.path(tempdir(), 'file.csv'), height = 'layer_top', gtype = 'gt1',
                          use.swisscode = TRUE, GrainSIZE = 'gs')
profile

## Note that generally in a snowprofile object layer properties can be custom named,
#  meta information, e.g. station_id, can not! I.e. you need to use the prescribed names.

Description

This routine reads blocks of snowprofile metadata, layers, tests, and stability signs. Columns contain different variables, rows different observations. While metadata only contains one row, layers, tests, and signs consist of potentially multiple rows. Within each block of information, mind the correct alignment of rows. Missing values (i.e., NA) need to be left blank or called NA. See the examples below including the example file shipped with the package.

Usage

snowprofileCsv_advanced(
  csvFile,
  meta = c("uid", "hs", "maxObservedDepth", "comment"),
  layers = c("depth", "height", "gtype", "hardness", "datetag", "gsize", "gtype_sec",
    "layer_comment"),
  tests = c("test", "result", "fract_char", "score", "test_depth", "test_comment"),
  instabilitySigns = c("instabilitySign_type", "instabilitySign_present",
    "instabilitySign_comment"),
  sep = ",",
  elev.units = "ft",
  tz = "UTC"
)

Arguments

Author(s)

fherla

Examples

## load example csv file that ships with package:
csvFile <- system.file('extdata', 'example_adv.csv', package = 'sarp.snowprofile')

profile <- snowprofileCsv_advanced(csvFile, meta = c("uid", "hs", "maxObservedDepth", "comment",
                                                     "datetime", "zone", "station",
                                                     "station_id", "aspect", "elev", "angle"))

plot(profile)

Description

Create a snowprofileInstabilitySigns object. Instability signs can for example be whumpfs, cracking, natural avalanches, skier accidental release, ski cutting, etc. For more information, see Canadian Avalanche Association. (2016). Observation Guidelines and Recording Standards for Weather, Snowpack, and Avalanches. Revelstoke, BC, Canada.

Usage

snowprofileInstabilitySigns(
  signsFrame = data.frame(type = as.character(NA), present = as.character(NA), comment =
    as.character(NA)),
  dropNAs = TRUE
)

Arguments

Details

Note: This class might be a temporary solution to digitize instability signs observed in proximity to snowprofiles. The information contained here, might be ported to a more general field observations class that is both independent from snowprofile objects and that is more in line with existing field observation standards.

Value

snowprofileInstabilitySigns object

Author(s)

fherla

See Also

snowprofile, snowprofileLayers, snowprofileTests

Examples

## create a data.frame with instability sign observations
(signsFrame <- data.frame(type = c("Na", "whumpf", "cracking", "Sa"),
                         present = c(FALSE, TRUE, FALSE, FALSE)))

## create snowprofileInstabilitySigns object
instabilitySigns <- snowprofileInstabilitySigns(signsFrame)

## create snowprofile object containing instability signs and check resulting object:
snowprofile(instabilitySigns = instabilitySigns)

Description

Helper function to conveniently create a snowprofileLayers object, i.e. data.frame with mandatory column fields height (or depth) that provides vertical position of layers. Layers need to be ordered in a sequential manner, and the routine will rearrange the layers so that the last row of the resulting dataframe corresponds to the snow surface. If the vertical location of the layers is given by depth, make sure to provide hs if it's known. Otherwise, provide the field maxObservedDepth or layer thicknesses. Providing only depth will issue a warning and set the corresponding lowest layer thickness to NA. The resulting dataframe will contain all three fields height, depth, and thickness, which will be auto-filled if not provided (see format_snowprofileLayers). If the columns that describe layer properties are not of equal lengths, their values will be recycled (default data.frame mechanism). Instead of individual layer characteristics, a data.frame can be provided, which will be converted into a snowprofileLayers class. The constructor asserts correctness of the layers object by a call to validate_snowprofileLayers.

Usage

snowprofileLayers(
  height = as.double(NA),
  temperature = as.double(NA),
  density = as.double(NA),
  lwc = as.double(NA),
  gsize = as.double(NA),
  gsize_max = as.double(NA),
  gsize_avg = as.double(NA),
  gtype = as.factor(NA),
  gtype_sec = as.factor(NA),
  hardness = as.double(NA),
  ddate = as.POSIXct(NA),
  bdate = as.POSIXct(NA),
  datetag = as.Date(NA),
  ssi = as.double(NA),
  sphericity = as.double(NA),
  v_strain_rate = as.double(NA),
  crit_cut_length = as.double(NA),
  tsa = as.double(NA),
  tsa_interface = as.double(NA),
  rta = as.double(NA),
  rta_interface = as.double(NA),
  layerOfInterest = as.logical(NA),
  comment = as.character(NA),
  ...,
  hs = as.double(NA),
  maxObservedDepth = as.double(NA),
  layerFrame = NA,
  validate = TRUE,
  dropNAs = TRUE
)

Arguments

Value

snowprofileLayers object as data.frame with strings as factors

Author(s)

shorton, fherla

See Also

snowprofile

Examples

## Empty layers object:
snowprofileLayers()


## simple layers example that recycles the hardness 1F+: with warning issued!
## Try what happens if you provide ddate as character array without a timezone.
snowprofileLayers(height = c(10, 25, 50),
                  hardness = char2numHHI('1F+'),
                  gtype = c('FC', NA, 'PP'),
                  ddate = as.POSIXct(c(NA, NA, "2020-02-15 10:45:00"),
                                     tz = "Etc/GMT+7"))

## create snowprofileLayers object from data.frame
## and feed it into a snowprofile object:
df <- data.frame(height = c(10, 25, 50),
                  hardness = c(2, 3, 1),
                  gtype = c('FC', NA, 'PP'),
                  stringsAsFactors = TRUE)

spL <- snowprofileLayers(layerFrame = df)
(sp <- snowprofile(layers = spL))


##### Create top-down recorded snowprofileLayers ####
## check out how the fields 'hs' and 'maxObservedDepth' are auto-filled in the
## resulting snowprofile object!
## 1.) Specify depth and hs:
## In that case the routine will assume that the deepest layer extends down to the ground
(sp1 <- snowprofile(layers = snowprofileLayers(depth = c(40, 25, 0),
                                               hardness = c(2, 3, 1),
                                               gtype = c('FC', NA, 'PP'),
                                               hs = 50)))
## note that sp and sp1 are the same profiles:
all(sapply(names(sp$layers), function(cols) {sp$layers[cols] == sp1$layers[cols]}), na.rm = TRUE)

## 2.) Specify depth, hs and thickness or maxObservedDepth:
## This will include a basal layer of NAs to fill the unobserved space down to the ground.
(sp2 <- snowprofile(layers = snowprofileLayers(depth = c(40, 25, 0),
                                               hardness = c(2, 3, 1),
                                               gtype = c('FC', NA, 'PP'),
                                               hs = 70,
                                               maxObservedDepth = 50)))

## 3.) Specify depth and maxObservedDepth:
## This will include a basal layer of NAs which is 1 cm thick to flag the unknown basal layers.
(sp3 <- snowprofile(layers = snowprofileLayers(depth = c(40, 25, 0),
                         hardness = c(2, 3, 1),
                         gtype = c('FC', NA, 'PP'),
                         gsize = c(2, NA, NA),
                         maxObservedDepth = 50)))

## 4.) Specify depth and thickness:
## This is equivalent to the example spL3 above!
## This will include a basal layer of NAs which is 1 cm thick to flag the unknown basal layers.
(sp4 <- snowprofile(layers = snowprofileLayers(depth = c(40, 25, 0),
                         thickness = c(10, 15, 25),
                         hardness = c(2, 3, 1),
                         gtype = c('FC', NA, 'PP'))))

## 5.) Specify only depth: issues warning!
(sp5 <- snowprofile(layers = snowprofileLayers(depth = c(40, 25, 0),
                         hardness = c(2, 3, 1),
                         gtype = c('FC', NA, 'PP'))))

## plot all 5 top.down-recorded profiles:
set <- snowprofileSet(list(sp1, sp2, sp3, sp4, sp5))
plot(set, SortMethod = "unsorted", xticklabels = "originalIndices",
     hardnessResidual = 0.1, hardnessScale = 1.5, TopDown = TRUE,
     main = "TopDown Plot")

plot(set, SortMethod = "unsorted", xticklabels = "originalIndices",
     hardnessResidual = 0.1, hardnessScale = 1.5, TopDown = FALSE,
     main = "BottomUp Plot")

Description

Read .prf files from SNOWPACK model output

Usage

snowprofilePrf(Filename, ProfileDate = NA, tz = "UTC")

Arguments

Details

Several SNOWPACK model output formats exist see SNOWPACK documentation

Definitions of PRF files are provided at https://models.slf.ch/docserver/snowpack/html/prf_format.html

PRF files typically contain profiles from the same station at multiple time steps. If a specific ProfileDate is provided a single snowprofile object is returned (search available dates with scanProfileDates), otherwise all profiles are read and a list of snowprofile objects is returned.

Value

a single snowprofile object of list of multiple snowprofile objects

Author(s)

shorton

See Also

snowprofilePro, scanProfileDates, snowprofileSno

Examples

## Path to example prf file
Filename <- system.file('extdata', 'example.prf', package = 'sarp.snowprofile')

## Scan dates in file
Dates <- scanProfileDates(Filename)
print(Dates)

## Read a single profile by date and plot
ProfileDate <- Dates[3]
Profile <- snowprofilePrf(Filename, ProfileDate = ProfileDate)
plot(Profile)

## Read entire time series and plot
Profiles <- snowprofilePrf(Filename)
plot(Profiles, main = 'Timeseries read from example.prf')

Description

Read .pro files from SNOWPACK model output

Usage

snowprofilePro(
  Filename,
  ProfileDate = NA,
  tz = "UTC",
  remove_soil = TRUE,
  suppressWarnings = FALSE
)

Arguments

Details

Several SNOWPACK model output formats exist see SNOWPACK documentation

Definitions of PRO files are provided at https://models.slf.ch/docserver/snowpack/html/pro_format.html and an example file is available at niViz

PRO files typically contain profiles from the same station at multiple time steps. If a specific ProfileDate is provided a single snowprofile object is returned (search available dates with scanProfileDates), otherwise all profiles are read and a list of snowprofile objects is returned.

Value

a single snowprofile object of list of multiple snowprofile objects

Author(s)

shorton

See Also

snowprofilePrf, scanProfileDates, snowprofileSno

Examples

## Path to example pro file
Filename <- system.file('extdata', 'example.pro', package = 'sarp.snowprofile')

## Download example pro file from niViz
#Filename <- tempfile(fileext = '.pro')
#download.file('https://niviz.org/resources/example.pro', Filename)

## Scan dates in file
Dates <- scanProfileDates(Filename)
print(Dates)

## Read a single profile by date and plot
ProfileDate <- Dates[3]
Profile <- snowprofilePro(Filename, ProfileDate = ProfileDate)
plot(Profile)

## Read entire time series and plot
Profiles <- snowprofilePro(Filename)
plot(Profiles, main = 'Timeseries read from example.pro')

Description

Constructor for class snowprofileSet

Usage

snowprofileSet(x = list())

Arguments

Value

a snowprofileSet

See Also

snowprofile, summary.snowprofileSet

Description

Read .sno files from SNOWPACK model input/output

Usage

snowprofileSno(Filename)

Arguments

Details

Several SNOWPACK model output formats exist see SNOWPACK documentation

Definitions of SNO files are provided at https://models.slf.ch/docserver/snowpack/html/smet.html

Value

a snowprofile object

Author(s)

shorton

See Also

snowprofilePro, snowprofilePrf, snowprofileCsv

Examples

## Path to example prf file
Filename <- system.file('extdata', 'example.sno', package = 'sarp.snowprofile')

## Read snowprofile object
Profile <- snowprofileSno(Filename)

## Note: plot.snowprofile won't work because sno files don't have harndess

## Plot a temperautre profile
plot(snowprofileSet(list(Profile)), ColParam = 'temp')

Description

Create a snowprofileTests object.

Usage

snowprofileTests(
  testsFrame = data.frame(type = as.character(NA), result = as.character(NA), score =
    as.double(NA), fract_char = as.character(NA), depth = as.double(NA), comment =
    as.character(NA)),
  dropNAs = TRUE
)

Arguments

Details

For more information, see Canadian Avalanche Association. (2016). Observation Guidelines and Recording Standards for Weather, Snowpack, and Avalanches (OGRS). Revelstoke, BC, Canada.

Value

snowprofileTests object

Author(s)

fherla

See Also

snowprofile, snowprofileLayers, snowprofileInstabilitySigns

Examples

## create a data.frame with test observations
(testsFrame <- data.frame(type = c("CT", "ST", "ECT"),
                         result = c("E-M", "M", "P"),
                         score = c(10, NA, 12),
                         fract_char = c("SP", NA, NA),
                         depth = c(40, 40, 40),
                         comment = c("some comment on first test", "", "")))

## create snowprofileTests object
tests <- snowprofileTests(testsFrame)

## create snowprofile object containing test results and check resulting object:
snowprofile(tests = tests)

Description

A list of 12 snowprofile objects.

Usage

SPgroup

Format

A list with 12 entries, that are of class snowprofile

See Also

SPpairs, SPtimeline, plot.snowprofileSet

Examples

plot(SPgroup, SortMethod = 'unsorted', xticklabels = "originalIndices")
plot(SPgroup, SortMethod = 'hs', xticklabels = "originalIndices")

Description

A list with two entries, each containing a snowprofile object. Both are malformatted, check out the examples in validate_snowprofile and reformat_snowprofile to learn how to fix it.

Usage

SPmalformatted

Format

A list with several entries, that are of class snowprofile

See Also

validate_snowprofile, reformat_snowprofile, SPpairs, SPgroup, SPtimeline

Description

A list with several entries, each containing a snowprofile object. Pairs of similar profiles are grouped by their names.

Usage

SPpairs

Format

A list with several entries, that are of class snowprofile

See Also

SPgroup, SPtimeline

Examples

## Each name refers to one snowprofile:
names(SPpairs)

opar <- par(no.readonly = TRUE)
par(mfrow = c(1, 2))
plot(SPpairs$A_manual, main = 'SPpairs$A_manual')
plot(SPpairs$A_modeled, main = 'SPpairs$A_modeled')
par(opar)

Description

Timeseries of snowprofiles #'

Usage

SPtimeline

Format

A list with several entries, that are of class snowprofile

See Also

SPgroup, SPpairs

Examples

summary(SPtimeline)
plot(SPtimeline)

Description

Summary of a single snowprofile

Usage

## S3 method for class 'snowprofile'
summary(object, fast = FALSE, ...)

Arguments

Details

Creates a one row data.frame where each column contains metadata.

Metadata is determines as elements of the snowprofile object list that are length = 1. An exception is made for latlon where separate columns for lat and lon are produces.

A derived value nLayers is derived by counting the number of rows in $layers.

Value

data.frame

Author(s)

shorton

See Also

summary.snowprofileSet

Examples

Profile <- SPgroup[[1]]
names(Profile)
summary(Profile)
lapply(SPgroup, summary)

Description

Wrapper for summary.snowprofile, which only returns metadata for a single snowprofile object. summary.snowprofileSet provides metadata for multiple snowprofiles, which is useful for subsetting.

Usage

## S3 method for class 'snowprofileSet'
summary(object, fast = TRUE, ...)

Arguments

Value

data.frame

Author(s)

shorton

See Also

summary.snowprofile, rbind.snowprofileSet

Examples

## Extract metadata for a group of profiles
Metadata <- summary(SPgroup)
head(Metadata)

## Subsetting profiles with Metadata
Alpine <- SPgroup[Metadata$elev > 2000]
summary(Alpine)
Shallow <- SPgroup[Metadata$hs < 150]
summary(Shallow)
Week2 <- SPtimeline[summary(SPtimeline)$date > '2017-12-15']


## time comparison of fast--slow implementation
## expect 20 sec runtime
# rbenchmark::benchmark(fast = {Metadata <- summary(SPgroup, fast = TRUE)},
#                       slow = {Metadata <- summary(SPgroup, fast = FALSE)},
#                       replications = 10**3)

Description

A character array of grain types that can be translated into a numerical code by their indices.

Usage

swisscode

Format

A character array

Examples

print(swisscode)

## see numerical code for each grain type:
rbind(swisscode, seq(length(swisscode)))

Description

Validator function that checks if snowprofile standards are being met and raises an error if mandatory fields are missing or data types are incorrect. The function raises a warning when unknown field names are encountered.

Usage

validate_snowprofile(object, silent = FALSE)

Arguments

Value

Per default an error is raised when discovered, if silent = TRUE the error is only printed and the error message returned (Note: a warning is never returned but only printed!). If the function is applied to multiple objects, the function returns NULL for each object if no error is encountered (see examples below).

See Also

reformat_snowprofile

Examples

## Validate individual snowprofile and raise an error
## in case of a malformatted profile:

## (1) no error
validate_snowprofile(SPgroup[[1]])

## (2) malformatted profile --> error
this_throws_error <- TRUE
if (!this_throws_error) {
validate_snowprofile(SPmalformatted[[1]])
}

## Validate a list of snowprofiles and raise an error
## when the first error is encountered:
## (i.e., stop subsequent execution)

## (1) no error
lapply(SPgroup, validate_snowprofile)

## (2) malformatted profile --> error
if (!this_throws_error) {
lapply(SPmalformatted, validate_snowprofile)
}

## Validate a list of snowprofiles and continue execution,
## so that you get a comprehensive list of errors of all profiles:
if (!this_throws_error) {
errorlist <- lapply(SPmalformatted, validate_snowprofile, silent = TRUE)
errorlist[sapply(errorlist, function(item) !is.null(item))]  # print profiles that caused errors
}

Description

Validator function that checks if class standards are being met and raises an error if not.

Usage

validate_snowprofileLayers(object, silent = FALSE)

Arguments

Value

Per default an error is raised when discovered, if silent = TRUE the error is only printed and the error message returned.

Description

Write data into a SMET file https://models.slf.ch/docserver/meteoio/SMET_specifications.pdf

Usage

writeSmet(smet, filename)

Arguments

Value

Generates smet file

Author(s)

fherla, shorton

See Also

readSmet, snowprofileSno, snowprofilePrf, snowprofilePro

Examples

## First read example smet file provided in package
(Wx = readSmet(system.file('extdata', 'example.smet', package = 'sarp.snowprofile')))

## Then write Wx to a new temp file and show the file
writeSmet(Wx, filename = file.path(tempdir(), 'file.smet'))
file.show(file.path(tempdir(), 'file.smet'))

## Check whether it can be read back in
(WxNew <- readSmet(file.path(tempdir(), 'file.smet')))